How do I put HP switch into configuration mode?

How do I put HP switch into configuration mode?

How do I put HP switch into configuration mode?

Configuration commands and the context configuration modes

  1. HP Switch(config)# interface c3-c6. HP Switch(eth-C5-C8)#
  2. HP Switch(eth-C5-C8)# HP Switch(eth-Trk1)#
  3. HP Switch(config)# vlan 100. Command executed at configuration level to enter VLAN 100 context.
  4. HP Switch(vlan-100)#
  5. HP Switch(vlan-100)#?

How do I reset my HP V1910 24g switch?

HP V1910-48G JE009A Factory reset – Password recovery capability enabled.

  1. Connect switch cable to COM.
  2. Open Putty on COM 38400 – 8 – 1 – N.
  3. Powercycle the switch.
  4. Press Ctrl-B at boot to enter extended boot menu.
  5. Skip current system configuration.
  6. Reboot.

How do I change the management IP on an HP switch?

Click on Quick Setup. In the Switch Quick Setup Parameters box, click on Change. Enter the IP address and any other information such as the Subnet mask and Gateway. Click on Save to save changes.

How do I configure my HP 1920 switch?

Initial configuration

  1. Place the switch close to the PC that will use for configuration.
  2. Connect power to the switch, and then start the PC (If it is not already running) and wait until the switch and PC have finished their start-up sequences.
  3. Connect the PC to any port on the switch using a standard Ethernet LAN cable.

How do I configure VLAN on HP switch?

Configuring basic VLAN settings

  1. Enter system view, use the command: system view.
  2. Create VLANs, use the command: vlan { vlan-id1 [ to vlan-id2 ] | all }
  3. Enter VLAN view, use the command: vlan vlan-id.
  4. Configure a name for the VLAN, use the command: name text.
  5. Configure the description of the VLAN, use the command:

How do you reset a HP 1920s switch?

To execute the factory default reset on the switch, perform these steps:

  1. Using a small, thin tool with blunt ends (such as a paper clip), press the Reset button on the front of the switch.
  2. Continue to press the Reset button until the Fault LED light begins to flash.
  3. Release the Reset button.

How do you manage a ProCurve switch?

How to: Configure a HP ProCurve switch

  1. Step 1: Connect your serial connection.
  2. Step 2: Conenct PuTTY.
  3. Step 3: Get the IP address.
  4. Step 4: Set time server.
  5. Step 5: Set SNMP community info.
  6. Step 6: Launch the web GUI.
  7. Step 7: Configure basic info.
  8. Step 8: Create VLANs.

How to get started with the HP v1910 switch series?

The HP V1910 Switch Series Getting Started Guid e describes the appearance, installation, power-on, maintenance, and troubleshooting of the HP V1910 switches. This preface includes:  Audience  Conventions  Contacting HP  Subscription service  Warranty  Documents Audience

What is the name of the HP switch series?

About the HP V1910 Switch Series. HP V1910 Switch Series is a line of Layer 2 Gigabit Ethernet switching products developed by Hewlett-Packard Development Company, L.P. (hereinafter referred to as HP).

Is the HP v1910-48g switch je006a equipped with one fan?

The HP V1910-24G Switch JE006A is equipped with one fan for heat dissipation. HP V1910-48G Switch JE009A Front panel Figure 5 HP V1910-48G Switch JE009A front panel

How to setup a switch on a HP laptop?

Anyway, heres a very quick run down on initial setup (assign IP and secure the system passwords). 1.