How do I reset my Cisco router to factory default?

How do I reset my Cisco router to factory default?

How do I reset my Cisco router to factory default?

  1. Prepare the router. Make sure the Cisco router is turned off and the power cord is plugged into both the router and the power source.
  2. Locate the reset button. Look for the small factory reset button on the back of the router.
  3. Use the reset button.
  4. Wait for the reset to complete.

How do I reset my Cisco 871 router to factory settings?

Reboot your Cisco 871 router

  1. First, open any internet browser (like Firefox or Google Chrome, etc).
  2. Go to the Maintenance or Tools tab.
  3. Then click Save and Restore settings or System options.
  4. Now click on Rebooting or Reboot the Device.
  5. In this step, Wait for a while, Now you are done Rebooting successfully.

How do I reset my Cisco 1800 factory default?

How to Factory Reset 1800 series Cisco router

  1. Connect you PC to the router via console cable and connect using Putty.
  2. Boot the router while holding ctrl and break get into rommon1>
  3. Type the following command.
  4. Type Reset to start the factory reset.
  5. To enter config mode, issue the config terminal command.

How do I Reset my Cisco 2800 router to factory settings?

Here’s what to do:

  1. Connect to the serial console.
  2. Power off the router and then power on.
  3. Send the router a BREAK.
  4. Type this command at the rommon prompt in order to boot from Flash.
  5. Reset the router.
  6. The router should now boot into the Initial config dialogue: Would you like to enter the initial configuration dialog? [

How do I Reset my Cisco router username and password?

To do this, press and hold the Reset button for 10 seconds. NOTE: Resetting your router to its default factory settings will also reset your router’s password. The router’s default password is “admin” as for the username, just leave the field blank.

How do I reset my Cisco 2800 router to factory settings?

What is the default Cisco username and password?

Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168. 1.1 or 192.168. 1.254.

How do I Reset my Cisco router to factory default?

How do I Reset my Cisco router to factory default?

  1. Prepare the router. Make sure the Cisco router is turned off and the power cord is plugged into both the router and the power source.
  2. Locate the reset button. Look for the small factory reset button on the back of the router.
  3. Use the reset button.
  4. Wait for the reset to complete.

How do I Reset a Cisco Packet Tracer router?

Follow these steps:

  1. Log on to your switch, and enter the privileged EXEC mode by entering enable and then entering the enable password command.
  2. Enter clear config all to reset the entire system. You don’t need to reload the switch because processing the command wipes the switch.

How do I clear the running config on a Cisco router?

To clear out the running config file, simply erase the startup config file and then reload the device.

How do I Reset my Cisco router password?

Step-by-Step Procedure

  1. Either switch off or shut down the router.
  2. Remove the compact flash that is on the rear of the router.
  3. Switch on the router.
  4. Once the router is on Rommon mode, reinsert the compact flash.
  5. Type confreg 0x2142 at the rommon 1> prompt in order to boot from Flash.
  6. Type reset at the rommon 2> prompt.

How do I Reset my Cisco 2960 to factory settings?

Reset a Cisco 2960 Switch To Factory Default Settings

  1. Connect up a console cable and power on the switch, whilst holding down the “mode” button:
  2. Run the following command to initialize the flash file system:
  3. Delete the config.text file from the flash directory:

Where is the Reset button on a Cisco router?

Press the Reset button located at the back of the device with a pin for approximately 15 seconds or until the power light on the front of the device starts flashing. The Router reloads and is set to the default configuration settings.

How do I reset my Cisco 3650 to factory settings?

Part A: First you need to power down the switch. Once the switch is powered off, hold down the mode button, and power the switch on. The switch will boot up and you should see the switch prompt as shown below.

What is default password for Cisco router?

admin
Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168. 1.1 or 192.168. 1.254.

How do I reset my Cisco 3750 to factory settings?

There is another method:

  1. Break the stack;
  2. Power up the switch individually;
  3. Hold down the “Mode” button for 30 seconds and release;
  4. The switch will reboot into factory default;
  5. Console into the switch;
  6. Delete the files VLAN.dat, VLAN.dat.backup, config.text, config.text.backup.
  7. Renumber the stack.